Router Configuration

Setting up in Router Mode

Open your browser and type http://192.168.2.1 to enter the web interface.
Click on Setup on the left
    Enter your VIF username with @vif.com
    Enter your VIF Password
Press Save Settings

Setting up in Bridge Mode

Type http://192.168.2.1 to enter the web interface. Click Mode On the left
Once in that page. Click Reset for Factory Reset
Finally Click Reboot and its set! Your modem is in Bridge Mode!

To configure the Speedtouch 510/516 modem/router to let it stay connected 24/7, you will need to edit a few configuration before log in into it.

1. Open up your Web Browser and type in http://192.168.1.254 in the address bar at the top and hit Enter.
2. Click on the SpeedTouch menu on the left.
3. Scroll down to the bottom of the page and click on the Set Up link.
4. A new page will open up. Click Next.
5. Select “Router” and click Next.
6. Select VPI/VCI as “0.35” and “PPP over ethernet” and press Next.
    - Enter your VIF Username with @vif.com
    - Password and Confirm Password and click Next.
7. Access control to be able to login to the modem next time
    - Enter a User Name
    - Password and Confirm Password click Next.
8. Click on Start to begin configuration of the modem.
9. Click on Finish when the modem is finished configuring
10. In a few minutes, try to browse the internet, you should be able to surf now. If it doesnt work, check the DSL Status to see if your connected or not.

Here is the guide to configure the TP-LINK TD-W8901G/TD-W8951ND Wireless Modem/Router

1. Type in http://192.168.1.1 in your web browser
2. Click on Interface Setup  on the top
    - Virtual Circuit:  set to PVC2
    - Select PPPoA/PPPoE next to Encapsulation
    - Enter your VIF Username@vif.com in the Username field
    - Enter your VIF Password
    - Make sure the Default Route is set to YES
    - Save the settings by pressing SAVE
3. To setup your wireless click on the Wireless Sublink under Interface Setup
    - Enter the right country in the Channel
    - change Use WPS to NO
    - Set Autentication Type to WPA-PSK/WPA2-PSK
    - Use Password encryption to TKIP/AES and put in password using 8-64 characters
    - Save the settings by pressing SAVE
4. Next go to Advanced Setup
    - Firewall and SPI make sure its set to Disabled
    - Save the settings by pressing SAVE
5. Click on Access Management then UPnP sublink
    - UPnP and Auto-Configured make sure its set to Activated
    - Save the settings by pressing SAVE
6. Finally Click on Maintenance and sublink Administration
    - put in a password to change the default admin password (this is recommended)
    - Save the settings by pressing SAVE

Here is the guide to configure the Totolink ND150/ND300 Wireless Modem/Router

1. Type in http://192.168.1.1 in your web browser
2. Click on Interface Setup  on the top
3. Virtual Circuit:  set to PVC2
    - VPI 0 / VCI 35
    - Select PPPoA/PPPoE next to Encapsulation
    - Enter your VIF Username@vif.com in the Username field
    - Enter your VIF Password
    - Next to Connection Settings choose Always on
    - Make sure the Default Route is set to YES
    - Get IP Address set to Dynamic
    - Save the settings by pressing SAVE
4. To setup your wireless click on the Wireless Sublink under Interface Setup
    - Enter the right country in the Channel
    - Set Autentication Type to WPA-PSK/WPA2-PSK
    - Use Password encryption to TKIP/AES and put in password using 8-64 characters
    - Save the settings by pressing SAVE
5. Next go to Advanced Setup
    - Firewall and SPI make sure its set to Disabled
    - Save the settings by pressing SAVE
6. Click on Access Management then UPnP sublink
    - UPnP and Auto-Configured make sure its set to Activated
    - Save the settings by pressing SAVE
7. Finally Click on Maintenance and sublink Administration
    - put in a password to change the default admin password (this is recommended)
    - Save the settings by pressing SAVE

Here is the guide to configure the Netis DL-4311

1. Type in http://192.168.1.1 in your web browser
2. Username/password is guest/guest
3. Click on Setup
4. Go to the bottom of the page to WAN Interface Table and click on WAN0
5. Next make sure all these informations are correct in this page.
    - VPI 0 / VCI 35
    - Channel Mode: PPPoE
    - PPPSettings: enter your VIF Username@vif.com and VIF Password
    - Click on Modify on the bottom of the page
6. Next click on WLAN on the left and click Basic
    - Enter an SSID and choose your Channel Number click Apply Changes
7. Next click on Security on the left
    - Encryption put WPA2 Mixed
    - Enter a password in the Pre-shared key
    - Click Apply Changes

Here is the guide to configure the Motorola Netopia 2210

1. Go to your browser and type http://192.168.1.254 and press enter
2. Default username and password is admin/admin to login
3. Once logged in Click on the Firewall link on the left and Click on the off button on the right page and save changes.
4. Next Click on Expert Mode. You will see a warning message just ignore it.
5. Click on Yes, Enter Expert Mode
6. Click on Configure on the left and click Connection
    - Set VCI to 0
    - Set VPI to 35
    - Protocol : PPP Over Ethernet/LLCSNAP
    - Bridging: Disabled
    - Concurrent Bridging/Routing: Disabled
    - Username: Enter your VIF Username@vif.com
    - Password: Enter your VIF Password
    - Confirm Password: Reenter your VIF Password
    - Connection Type: Always On
    - UPNP: Have a check mark
    - Click Save Changes
7. Click on Restart Router on the left
8. Click Yes to restart
9. Your modem will reboot and in about 2 mins you will see 4 green lights on your modem which indicates you are now connected to your internet.

Here is the guide to configure the 2Wire 2701HG/2700HG-E

1. Open a browser, in the address bar, type 192.168.1.254.
2. Click on “Internet Connection”.
3. Click on “Advanced Settings” and it will ask you for a password to login, type: admin.
4. Make sure the Settings is on DSL
    - Put the DSL Line Selection to “Automatic” then enter VPI as “0” and VCI as “35”.
    - Set the ATM Encapsulation as “Bridged LLC”.
    - Set the ATM PVC Search to “Disable”.
    - Set connection Type as “PPPoE”.
    - Enter your “username”, “password” and “confirm password”.
    - Set forced Upstream MTU as “1492”.
    - Click Save.
5. In a few minutes, try to browse the internet, you should be able to surf now.
6. If you want to setup the wireless, here are the instructions for it.
    - Go on the “Home Network” page, then in “Wireless Settings”
    - Put a check mark on “SSID Broadcast” and “Wireless Network Security”
    - The Authentication could be set on WEP Open, WEP Share, WPA-PSK, best choice will be “WPA-PSK”.
    - Use “Custom encryption key” and type the key you want. The default one is the one on the modem.
    - Finally, click “Save”.

Here is a guide to get your SmartRG SR505N connected in PPPoE mode for FTTN25 and FTTN50 speeds

1. Type in http://192.168.1.1 in your web browser
2. Click on Manage Gateway (advanced)
3. Click on WAN service on the left and then click Add
    - PPP Username: VIF Username@vif.com
    - Password: VIF Password
    - Uncheck Enable Firewall
    - Check Enable NAT and Enable SIP
    - Click Next until you get a save button
    - Click on the DSL link on the left
    - This page make sure the Enable PTM is checked and click Save.
4. Click on Wireless to begin setting up your Wifi
    - Click on Basic on the left
    - Enable Wireless make sure its checked
    - SSID: Enter any name you would like for your wireless name to appear
    - Click on Security on the left side
    - Network Authentication: set to WPA2/WPA-PSK
    - WPA /WAPI Passphrase: put a wifi password
    - click on Apply/Save

With Cable modems, installation is very simple. Its a simple plug and play. All you need to do is plug in the modem and coaxial cable and ethernet wire to your PC or router and wait for it to connect to the cable network. Once the online light or internet light is on, you can surf the web.

Here is the guide to configure the Linksys PAP2T

1. You must connect your ATA to your router in order to get an IP address
2. Pick up your phone and dial 4 times *
3. Once the operator is asking to enter an option, dial 110#. get the IP address needed in order to access the PAP2T
4. Once you are in the device use these steps to configure your ATA.
5. Click on Admin login on the left and then Switched to Advanced View in the middle
6. System Tab
    - Primary NTP Server: time.nist.gov
    - Secondary NTP Server: pool.ntp.org
7. Provisionning Tab
    - Provision Enable: Yes
    - Profile Rule: http://bill2.vif.com/$A/$MA.cfg
    - GPP A: 2
8. Regional Tab
    - Ring Waveform: Sinusoid
    - Ring Frequency: 25
    - Ring Voltage: 70
    - TimeZone: GMT -05:00
    - Daylight Savings Time Rule: start=3/8/7/2:00;end=11/1/7/2:00;save=1
9. Line 1
    - Line Enable: Yes
    - NAT Mapping Enable: Yes
    - NAT Keep Alive: Yes
    - SIP Port: 5060
    - Proxy: sipshield1.vif.com
    - User ID: Your SIP ID
    - Password: Your SIP Password
    - Dial Plan: `(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|[2-9]xx[2-9]xxxxxxS0|xxxxxxxxxxxx.)`
10. Click Save Settings

Here is the guide to configure the Linksys RT31P2

1. To access the interface go here: http://192.168.15.1
2. The username and password are both “admin”
3. Go on the “Voice” tab, then go on “Line 1”
    - Input your SIP ID in your UserID
    - Type in the password in the Authentication Password.
    - Lastly Register/Proxy Server  type in “sipshield1.vif.com”.
4. Go at the bottom of the page and click on “Save Settings”.

Here is the guide to configure the Linksys WRTP54G

1. To access the interface go here: http://192.168.15.1
2. The username and password are both “admin”
3. (Optional) Click on the Wireless tab to set up wireless accessiblity.
4. Click on the Voice Tab and then click on admin login and switched to advanced view
5. System Tab
    - Primary NTP Server: time.nist.gov
    - Secondary NTP Server: pool.ntp.org
6. Provisionning Tab
    - Provision Enable: Yes
    - Profile Rule: http://bill2.vif.com/$A/$MA.cfg
    - GPP A: 2
7. Regional Tab
    - Ring Waveform: Sinusoid
    - Ring Frequency: 25
    - Ring Voltage: 70
    - TimeZone: GMT -05:00
    - Daylight Savings Time Rule: start=3/8/7/2:00;end=11/1/7/2:00;save=1
8. Line 1 Tab
    - Line Enable: Yes
    - NAT Mapping Enable: Yes
    - NAT Keep Alive: Yes
    - SIP Port: 5060
    - Proxy: sipshield1.vif.com
    - User ID: Your SIP ID
    - Password: Your SIP Password
    - Dial Plan: `(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|[2-9]xx[2-9]xxxxxxS0|xxxxxxxxxxxx.)`
    - Click Save Settings

Here is the guide to configure the Grandstream HT486

1. To access the interface go here: http://192.168.2.1
2. Next you need to type in "admin" and press enter .
3. Click on Advanced Settings.
    - SIP Server: sipshield1.vif.com
    - SIP User ID: Enter your SIP ID Authenticate Password: Enter your VoIP Password
4. Next we scroll down to "Register Expiration" set it to 600 seconds.
5. Now we scroll down to “Enable Call Features”
    - "Enable Call Features": must be set to Yes
    - Send DTMF: set to via RTP (RFC2833) and remove in-audio
6. Set Reply to ICMP on WAN port to YES
7. Set WAN Side HTTP Access  to YES
8. Now go all the way to the bottom and click Update.

Here is the guide to configure the Grandstream HT702

1. Plug in a phone and dial *** and then 02 to get IP of the unit
2. Enter the IP address in the browser and type in the password: admin and press enter
3. Config Basic Settings
    End User Password: account password
    Web Port: 8080
    Time Zone: GMT -5:00
    Click UPDATE
4. Config FXS Port1
    - Primary SIP Server: sipshield1.vif.com
    - NAT Traversal: Keep-Alive
    - SIP User ID:
    - Authenticate Password: Password for voip
    - Name: Name for display
    - Register Expiration: 600
    - Preferred DTMF method: Put all of them to RFC2833
    - Send Hook Flash Event: Yes
    - Dial Plan: `{ *xx | [34589]11 | [2-9]xx[2-9]xxxxxx | 1[2-9]xx[2-9]xxxxxx | 011x+ }`
    - UPDATE then reboot